Manufacturer-recommended service intervals and open recall alerts for your 1996 Plymouth Breeze.
ZIP unlocks trusted shops near you. Mileage unlocks personalized service due dates. Either or both — your call.
Your ZIP stays with us. We share your city with shops, never your ZIP. Read our Promise →
SUSPENSION:FRONT:CONTROL ARM:LOWER ARM
Campaign #10E059000 · Dec 27, 2010
Issue: FEDERAL-MOGUL IS RECALLING CERTAIN REPLACEMENT CONTROL ARM ASSEMBLIES, PART NUMBERS K7425, 10945, FA4510X, K7427, 10946, AND FA4611X, SOLD FOR USE ON VARIOUS PASSENGER VEHICLES LISTED ABOVE. THE BALL JOINT ON THE CONTROL ARM ASSEMBLY CAN FAIL CAUSING THE BALL STUD TO WEAR THROUGH THE CONTROL ARM HOUSING RESULTING IN NOISE AND/OR SEPARATION OF THE BALL STUD FROM THE HOUSING.
Risk: IF THERE IS A SEPARATION OF THE BALL STUD FROM THE HOUSING, THE DRIVER CAN LOOSE STEERING CONTROL, POSSIBLY RESULTING IN A VEHICLE CRASH.
Fix: FEDERAL-MOGUL WILL NOTIFY OWNERS OF RECORD AND REPLACE THE AFFECTED CONTROL ARMS FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JANUARY 28, 2011. OWNERS MAY CONTACT FEDERAL-MOGUL AT 1-877-489-6659.
SUSPENSION:FRONT:CONTROL ARM:LOWER BALL JOINT
Campaign #09E056000 · Sep 10, 2009
Issue: QUALIS AUTOMOTIVE IS RECALLING CERTAIN AFTERMARKET BALL JOINTS SOLD FOR USE ON CERTAIN PASSENGER VEHICLES. THE SOCKET MAY HAVE BEEN EXCESSIVELY HARDENED WHICH COULD CAUSE IT TO CRACK NEAR THE RETAINING RING GROOVE ALLOWING THE BALL STUD TO SEPARATE UNDER IMPACT LOAD. THE SUBJECT BALL JOINTS WERE SOLD AS FOUR PART NUMBERS, D10945, D10946, G10945, AND G10946. THE AFFECTED CONTROL ARMS, D10945 AND D10946, ARE STAMPED WITH THE FOLLOWING DATES ON THE BALL JOINTS: 134308, 135708, 100109, 102709, 104109, 105509, 107609, 108909, 110309, 113209, AND 116609. THE G10945 AND G10946 ARE THE SAME PART AS THE D10945 AND D10946 RESPECTIVELY. THEY ARE LABELED DIFFERENTLY DEPENDING ON THE AFTERMARKET CUSTOMER.
Risk: SEPARATION OF THE BALL STUD FROM THE SOCKET OF THE BALL JOINT HOUSING WOULD ALLOW THE CONTROL ARM TO COLLAPSE AND THE WHEEL TO FOLD IN CAUSING LOSS OF STEERING CONTROL, POSSIBLY RESULTING IN A CRASH.
Fix: QUALIS AUTOMOTIVE WILL REPLACE THE BALL JOINTS FREE OF CHARGE. THE SAFETY RECALL BEGAN ON NOVEMBER 9, 2009. OWNERS MAY CONTACT QUALIS AUTOMOTIVE AT 1-800-493-4128.
FUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP
Campaign #06E091000 · Feb 11, 2006
Issue: CERTAIN AIRTEX FUEL PUMP MODULES, P/NOS. E7089M, E7094M, E7113M, AND E7129M, MANUFACTURED BETWEEN JUNE 1 AND SEPTEMBER 24, 2006. THESE FUEL PUMP MODULES WERE SOLD AS AFTERMARKET FOR USE IN CERTAIN DAIMLERCHRYSLER VEHICLES LISTED ABOVE. SILICONE MATERIAL USED IN MANUFACTURE OF THE FLAPPER VALVE WAS OUT-OF-SPECIFICATION, LEADING TO EXCESS SWELL OF THE FLAPPER VALVE RESTRICTING THE FLOW OF FUEL TO THE FUEL PUMP MODULE.
Risk: FUEL RESTRICTION COULD RESULT IN LOSS OF POWER AND/OR ENGINE STALL, POSSIBLY RESULTING IN A VEHICLE CRASH.
Fix: AIRTEX WILL NOTIFY OWNERS AND REPLACE THE DEFECTIVE FUEL PUMP MODULES FREE OF CHARGE. THE RECALL BEGAN ON OCTOBER 18, 2006. OWNERS MAY CONTACT AIRTEX TOLL-FREE AT 1-866-867-3759.
FUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP
Campaign #06E088000 · Oct 23, 2006
Issue: CERTAIN TIGAS FUEL PUMP MODULES MANUFACTURED BETWEEN JUNE 1 AND SEPTEMBER 24, 2006, SOLD UNDER VARIOUS BRAND NAMES AND P/NOS. THESE FUEL PUMP MODULES ARE SOLD AS AFTERMARKET FOR USE IN CERTAIN DAIMLERCHRYSLER VEHICLES LISTED ABOVE. SILICONE MATERIAL USED IN MANUFACTURE OF THE FLAPPER VALVE WAS OUT-OF-SPECIFICATION, LEADING TO EXCESS SWELL OF THE FLAPPER VALVE RESTRICTING THE FLOW OF FUEL TO THE FUEL PUMP MODULE.
Risk: FUEL RESTRICTION COULD RESULT IN LOSS OF POWER AND/OR ENGINE STALL, POSSIBLY RESULTING IN A VEHICLE CRASH.
Fix: TI AUTOMOTIVE WILL NOTIFY OWNERS AND REPLACE THE DEFECTIVE FUEL PUMP MODULES FREE OF CHARGE. THE RECALL BEGAN ON OCTOBER 6, 2006. OWNERS MAY CONTACT TI AUTOMOTIVE TOLL-FREE AT 1-877-461-1834.
STRUCTURE:BODY:HOOD:HINGE AND ATTACHMENTS
Campaign #97V095000 · Jun 6, 1997
Issue: VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE SECONDARY HOOD LATCH SPRING CAN DISENGAGE FROM ITS RETENTION HOLE IF THE HOOD IS SLAMMED SHUT.
Risk: IF THIS CONDITION OCCURS SIMULTANEOUSLY WITHOUT ENGAGING THE PRIMARY LATCH, THE HOOD WOULD NOT BE RESTRAINED INCREASING THE RISK OF A VEHICLE CRASH.
Fix: DEALERS WILL REPLACE THE SECONDARY HOOD LATCH SPRING WITH A LONGER END HOOK SPRING.
POWER TRAIN:AUTOMATIC TRANSMISSION:LEVER AND LINKAGE:FLOOR SHIFT
Campaign #04V021000 · Jan 13, 2004
Issue: ON CERTAIN PASSENGER VEHICLES, THE FLOOR SHIFTER IGNITION-PARK INTERLOCK MAY FAIL AND ALLOW THE SHIFTER TO BE MOVED OUT OF THE PARK POSITION WITH THE KEY REMOVED. AN INOPERATIVE INTERLOCK MAY ALSO ALLOW THE KEY TO BE REMOVED WHEN THE SHIFTER HAS NOT BEEN PLACED IN THE PARK POSITION.
Risk: EITHER CIRCUMSTANCE MAY RESULT IN THE VEHICLE ROLLING AWAY WITHOUT WARNING.
Fix: DEALERS WILL INSTALL A NEW LOAD-LIMITING PUSH ROD INTO THE FLOOR SHIFTER LEVER OF THE AFFECTED VEHICLES. OWNER NOTIFICATION BEGAN ON JUNE 14, 2004. OWNERS SHOULD CONTACT DAIMLERCHRYSLER AT 1-800-853-1403.
SUSPENSION:FRONT:CONTROL ARM:LOWER BALL JOINT
Campaign #97V201000 · Nov 13, 1997
Issue: VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE LOWER CONTROL ARM BALL JOINT CAN SEPARATE DUE TO LOSS OF LUBRICATION.
Risk: SEPARATION OF THE BALL JOINT COULD CAUSE A LOSS OF STEERING CONTROL INCREASING THE RISK OF A VEHICLE CRASH.
Fix: DEALERS WILL INSPECT THE BALL JOINT END HOUSING COVER SEAL FOR LEAKAGE WITH A HIGH PRESSURE AIR TESTER AND THE RUBBER BOOT WILL BE VISUALLY INSPECTED FOR DAMAGE. IF THE COVER SEAL LEAKS OR THE BOOT IS DAMAGED, THE LOWER CONTROL ARM WILL BE REPLACED.
SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:MASTER CYLINDER
Campaign #96V075000 · Mar 5, 1996
Issue: THE BRAKE MASTER CYLINDER CAN LEAK BRAKE FLUID DUE TO A DAMAGED DOUBLE LIP REAR PISTON SEAL.
Risk: BRAKE FLUID LEAKAGE CAN RESULT IN DIMINISHED EFFECTIVENESS OF ONE HALF OF THE SPLIT BRAKE SYSTEM. THE INSTRUMENT PANEL WARNING LIGHT(S) WILL SIGNAL SYSTEM IMPAIRMENT PRIOR TO PARTIAL BRAKE SYSTEM LOSS.
Fix: DEALERS WILL REPLACE THE REAR BRAKE MASTER CYLINDR PISTON ASSEMBLY.
POWER TRAIN:AUTOMATIC TRANSMISSION:PARK/NEUTRAL START INTERLOCK SWITCH
Campaign #98V183000 · Jun 8, 1998
Issue: VEHICLE DESCRIPTION: PASSENGER VEHICLES EQUIPPED WITH AUTOMATIC TRANSMISSIONS. THE ADJUSTMENT OF THE CABLE CONNECTING THE CONSOLE SHIFTER MECHANISM TO THE IGNITION KEY CAN CAUSE A TRAPPED KEY CONDITION WHICH CAN RESULT IN A LOW FORCE REQUIRED TO DEPRESS THE SHIFT BUTTON. A COMBINATION OF APPLYING A MIS-ADJUSTED RELEASE BUTTON WITH A LOW FORCE ATTEMPT TO SHIFT OUT OF PARK WITH THE KEY IN THE LOCKED POSITION, CAN BREAK THE CONNECTING PIN IN THE SHIFTER.
Risk: IF THIS HAPPENS, THE "IGNITION-PARK" INTERLOCK SYSTEM WILL BE NONFUNCTIONAL.
Fix: DEALERS WILL INSPECT FOR PROPER OPERATION OF THE SYSTEM. ANY VEHICLES THAT ARE NOT FUNCTIONAL AFTER THE INSPECTION WILL HAVE THE SHIFT MECHANISM AND CABLE REPLACED WITH A "SELF-ADJUSTING" DESIGN.
SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP
Campaign #96V074000 · Feb 5, 1996
Issue: CORROSION OF THE ABS HYDRAULIC CONTROL UNIT CAN CAUSE THE SOLENOID VALVES TO STICK IN THE OPEN POSITION.
Risk: IF EITHER FRONT WHEEL VALVE STICKS, THE VEHICLE WOULD SWERVE FROM A STRAIGHT STOP WHEN THE BRAKES ARE APPLIED.
Fix: DEALERS WILL INSTALL A PLATE AND SILICONE GREASE INJECTED INTO THE SOLENOID CAVITY TO ELIMINATE THE POTENTIAL FOR THIS CONDITION.
Critical for safety and preventing major damage
Replace engine oil and oil filter. Modern synthetic oil lasts 7,500–10,000 miles.
Estimated cost — typical U.S. ranges
Dealer
~$120–$160
Shop
~$85–$115
DIY
~$25–$55
Full synthetic costs more than conventional. 5-quart 0W-20 + filter is the typical bill.
Rotate tires to ensure even wear and extend tire life.
Estimated cost — typical U.S. ranges
Dealer
~$85
Shop
~$60
DIY
Free
Often free at the shop where you bought the tires — worth asking before paying.
Inspect brake pads, rotors, and fluid. Replace pads if worn below minimum thickness.
Estimated cost — typical U.S. ranges
Dealer
~$85
Shop
~$60
DIY
Free
Most shops do this free as a courtesy with any service. Don't pay separately if you can avoid it.
Replace timing belt (if applicable). Critical failure can cause major engine damage.
Estimated cost — typical U.S. ranges
Dealer
~$935–$1175
Shop
~$655–$825
DIY
Pro only
On interference engines, a snapped belt destroys valves. Worth doing on schedule. Bundle water pump + tensioner — labor is already there.
Keeps your vehicle running smoothly and efficiently
Replace the engine air filter to maintain fuel efficiency and engine performance.
Estimated cost — typical U.S. ranges
Dealer
~$60–$95
Shop
~$45–$70
DIY
~$15–$40
5-minute job on most cars; the airbox lid usually has clips, no tools needed.
Flush and replace engine coolant to prevent overheating and corrosion.
Estimated cost — typical U.S. ranges
Dealer
~$285–$330
Shop
~$200–$235
DIY
~$25–$60
Use the manufacturer-specified coolant — wrong color/chemistry can damage the cooling system.
Replace transmission fluid to keep shifts smooth and prevent wear.
Estimated cost — typical U.S. ranges
Dealer
~$330–$500
Shop
~$235–$355
DIY
~$60–$180
Some sealed transmissions have no dipstick — fill is precise and best left to a shop. Many drivers can still DIY drain-and-fill.
Replace spark plugs for optimal combustion, fuel economy, and performance.
Estimated cost — typical U.S. ranges
Dealer
~$285–$390
Shop
~$200–$275
DIY
~$25–$100
Iridium plugs cost more but last 100k+ miles. V6/V8 access varies wildly — some are tough.
Inspect and replace the serpentine belt to avoid unexpected breakdowns.
Estimated cost — typical U.S. ranges
Dealer
~$195–$235
Shop
~$135–$165
DIY
~$20–$50
DIY-friendly if you can reach the tensioner. Inspect for cracks rather than swap on a strict mileage interval.
Extends the life of your vehicle and improves comfort
Replace the cabin air filter for clean air inside the vehicle.
Estimated cost — typical U.S. ranges
Dealer
~$60–$95
Shop
~$45–$70
DIY
~$15–$40
Usually behind the glovebox. Shops charge labor for a 10-minute job — easy DIY win.
Test battery health and clean terminals. Average battery life is 3–5 years.
Estimated cost — typical U.S. ranges
Dealer
~$225–$390
Shop
~$160–$280
DIY
~$130–$250
Most auto-parts stores test and install batteries free with purchase. Skip the dealer markup.
Check and replace power steering fluid to maintain steering responsiveness.
Estimated cost — typical U.S. ranges
Dealer
~$185–$220
Shop
~$130–$155
DIY
~$15–$40
Most cars built after ~2012 use electric power steering and have no fluid to service.
What drivers and federal regulators have officially reported about the 1996 Plymouth Breeze.
NHTSA has 198 complaints on file for the 1996 Plymouth Breeze (1996-08 → 2007-10). We haven't reviewed and grouped them yet for this specific vehicle — for now, the full list lives on NHTSA.
Top reported components: ENGINE AND ENGINE COOLING (100) · POWER TRAIN (26) · SERVICE BRAKES (24)
Note: NHTSA also opened 1 defect investigation(s) on this vehicle that closed without action.
Issues on other model years
Source: NHTSA Office of Defects Investigation (ODI). Complaint data refreshed Jul 20, 2026. Investigation data refreshed Jul 26, 2026.
We display NHTSA's record with attribution; we don't editorialize on what these complaints mean for any specific vehicle.
Typical U.S. ranges. Actual quotes vary by shop, parts choice, and vehicle condition.
How we estimate: Dealer = OEM parts × 1.4 + labor × $165/hr. Shop = parts + labor × $115/hr. DIY = parts only.
This maintenance schedule for the 1996 Plymouth Breeze reflects general industry intervals for modern vehicles. Your actual service needs may vary based on driving conditions, climate, and vehicle usage. Always consult your owner's manual for model-specific recommendations.