| EA21002 | open | Desiccated Air Bag Inflator Rupture | AIR BAGS:FRONTAL:DRIVER SIDE:INFLATOR MODULE | 2021-09-17 | · | · | From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open. |
| EA15003 | closed | Pedal Operation Interference | SERVICE BRAKES, HYDRAULIC | 2015-04-01 | 2015-09-01 | 15V507000 | On August 11, 2015, Nissan North America, Inc., submitted a Defect Information Report (DIR) describing a condition that may impede the driver's ability to transition quickly and smoothly from the accelerator pedal to the brake pedal in certain model year (MY) 2012 through 2015 Nissan Versa Sedans and MY 2014 through 2015 Nissan Versa Note vehicles (NHTSA Recall No. 15V-507).According to Nissan's DIR, in certain circumstances related to driver foot position and shoe type, the right edge of the driver?s shoe may catch the edge of the center console lower trim panel.Nissan indicated that this con |
| PE14014 | closed | Excessive Brake Pedal Travel | SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:MASTER CYLINDER | 2014-05-20 | 2015-05-13 | · | On May 20, 2014, ODI opened PE14-014 based on eight complaints alleging incidents of excessive brake pedal travel in model year (MY) 2013 through 2014 Nissan Sentra, Versa Sedan and Versa Note passenger cars (Figure 1) and information in Early Warning Reporting field reports indicating issues with master cylinder internal seals.In response to an information request letter sent by ODI, Nissan identified a condition with the master cylinder in early production subject vehicles that could result in a slow internal leak past one of the recuperating seals to the brake reservoir when the brake pedal |
