Ford Edge: nhtsa investigations
All rows for this model in the NHTSA investigations dataset, newest model year first. Each year links to its consumer page, which shows the same records with context.
| rows | 17 |
|---|---|
| model years | 2011–2022 (11) |
| data through | 2026-09-20 |
| method | /data/methodology#investigations |
| license | CC BY 4.0 (derived) |
Vehicle pages
2022 · 2021 · 2020 · 2018 · 2017 · 2016 · 2015 · 2014 · 2013 · 2012 · 2011
Rows
| year | action_number | status | subject | components | opened | closed | recall_campaign | summary |
|---|---|---|---|---|---|---|---|---|
| 2022 | EA23002 | closed | Loss of Motive Power | ENGINE | 2023-09-29 | 2024-10-31 | 24V635 | On July 22, 2022, the Office of Defects Investigation (ODI) granted a Defect Petition (DP22001) and opened a Preliminary Evaluation (PE22007) to investigate allegations of loss of motive power in model year (MY) 2021 Ford Bronco vehicles equipped with 2.7L EcoBoost engines. Complainants were reporting sudden engine failure while driving resulting in a loss of motive power, often without the ability to restart. During PE22007, the cause of engine failure and loss of motive power in the subject vehicles was determined to be intake valve fracture, and the full scope of vehicles affected by the su |
| 2021 | EA23002 | closed | Loss of Motive Power | ENGINE | 2023-09-29 | 2024-10-31 | 24V635 | On July 22, 2022, the Office of Defects Investigation (ODI) granted a Defect Petition (DP22001) and opened a Preliminary Evaluation (PE22007) to investigate allegations of loss of motive power in model year (MY) 2021 Ford Bronco vehicles equipped with 2.7L EcoBoost engines. Complainants were reporting sudden engine failure while driving resulting in a loss of motive power, often without the ability to restart. During PE22007, the cause of engine failure and loss of motive power in the subject vehicles was determined to be intake valve fracture, and the full scope of vehicles affected by the su |
| 2020 | RQ21002 | open | Rearview Camera FMVSS 111 Noncompliance | BACK OVER PREVENTION: SENSING SYSTEM: CAMERA | 2021-08-03 | · | · | On September 23, 2020, Ford Motor Company (Ford) filed a noncompliance recall report under 49 CFR Part 573 (NHTSA Recall No. 20V-575), recalling 620,246 Model Year (MY) 2020 Ford F-150, F-250, F-350, F-450, F-550, Explorer, Mustang, Transit, Expedition, Escape, Ranger and Edge, and Lincoln Nautilus and Corsair vehicles for a noncompliance with Federal Motor Vehicle Safety Standard (FMVSS) 111, Rear Visibility. Ford's recall described the noncompliance as insufficient electrical conductivity within the printed circuit board (PCB) internal to the camera leading to intermittent rearview camera operation. The supplier of the cameras was Magna Electronics.According to Ford's chronology in the Part 573, during the period February-April 2020, Ford identified and monitored warranty claims pertaining to intermittent or inoperative rearview cameras. Ford reviewed supplier product changes, focusing on changes introduced by the supplier in the October-November 2019 time frame. The Part 573 stated that the issue was brought to Ford's Critical Concerns Review Group (CCRG) for review on May 12, 2020.On July 7, 2020, NHTSA's Vehicle Research and Testing Center (VRTC) informed the Office of Defects Investigation (ODI) of a trend of MY 2020 Escape vehicles with rearview camera malfunctions. ODI contacted Ford the next day, providing five Vehicle Owner Questionnaires (VOQs) alleging inoperative rearview cameras. On July 15, 2020, Ford met with NHTSA to discuss the rearview camera issue. In a subsequent August 24, 2020 meeting, ODI and NHTSA's Office of Vehicle Safety Compliance (OVSC) met with Ford to discuss the recall status and additional VOQs. Ford presented rate and scope data for many of its MY 2020 products during the August 2020 meeting indicating high failure rates for certain models.This RQ is being opened to investigate both the timeliness and scope of Ford's rearview camera recall (20V-575), and Ford's compliance with reporting requirements.The subject reports referenced in the opening resume are identified by the following ODI reference numbers which can be reviewed at NHTSA.gov: 11349813, 11344126, 11342696, 11341486, 11340254, 11337274, 11331444, 11330875, 11329235, 11316960, 11343521, 11341884, 11337226, 11344018, and 11339573. |
| 2018 | DP26008 | open | Loss of Motive Power | ENGINE AND ENGINE COOLING | 2026-09-03 | · | · | The Office of Defects Investigation (ODI) received a petition on August 5, 2026, requesting a defect investigation into the 2.0 Liter EcoBoost engine on model year 2015-2018 Ford Edge vehicles. The petition alleges that engine coolant intrusion results in a significant loss of engine power, accompanied by an "Engine Coolant Over Temperature" warning message. The petition further alleges that after the vehicle has sat and cooled down, the engine runs roughly and generates a check engine light for a cylinder misfire. This defect petition is being opened to evaluate the issue and determine whether to grant or deny the petition. The petition can be reviewed at NHTSA.gov under ODI number 11754989. |
| 2017 | DP26008 | open | Loss of Motive Power | ENGINE AND ENGINE COOLING | 2026-09-03 | · | · | The Office of Defects Investigation (ODI) received a petition on August 5, 2026, requesting a defect investigation into the 2.0 Liter EcoBoost engine on model year 2015-2018 Ford Edge vehicles. The petition alleges that engine coolant intrusion results in a significant loss of engine power, accompanied by an "Engine Coolant Over Temperature" warning message. The petition further alleges that after the vehicle has sat and cooled down, the engine runs roughly and generates a check engine light for a cylinder misfire. This defect petition is being opened to evaluate the issue and determine whether to grant or deny the petition. The petition can be reviewed at NHTSA.gov under ODI number 11754989. |
| 2017 | EA21002 | open | Desiccated Air Bag Inflator Rupture | AIR BAGS:FRONTAL:DRIVER SIDE:INFLATOR MODULE | 2021-09-17 | · | · | From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open. |
| 2017 | PE24027 | closed | Loss of braking caused by rear brake hose failure | SERVICE BRAKES | 2024-10-03 | 2025-10-30 | 25V544 | On October 3, 2024, NHTSA’s Office of Defects Investigation (ODI) opened this Preliminary Evaluation to investigate instances of rear brake hose ruptures causing a sudden and unexpected loss of braking in model year (MY) 2015-2017 Ford Edge vehicles manufactured by Ford Motor Company. The complaints allege that, without warning, the vehicle lost its ability to brake causing an unanticipated increase in the vehicle’s stopping distance. The complaints also allege that, prior to the rear brake hose rupture event, the vehicle had been serviced under recall 20V-469. Recall 20V469 involved MY 2015-2 |
| 2016 | DP26008 | open | Loss of Motive Power | ENGINE AND ENGINE COOLING | 2026-09-03 | · | · | The Office of Defects Investigation (ODI) received a petition on August 5, 2026, requesting a defect investigation into the 2.0 Liter EcoBoost engine on model year 2015-2018 Ford Edge vehicles. The petition alleges that engine coolant intrusion results in a significant loss of engine power, accompanied by an "Engine Coolant Over Temperature" warning message. The petition further alleges that after the vehicle has sat and cooled down, the engine runs roughly and generates a check engine light for a cylinder misfire. This defect petition is being opened to evaluate the issue and determine whether to grant or deny the petition. The petition can be reviewed at NHTSA.gov under ODI number 11754989. |
| 2016 | EA21002 | open | Desiccated Air Bag Inflator Rupture | AIR BAGS:FRONTAL:DRIVER SIDE:INFLATOR MODULE | 2021-09-17 | · | · | From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open. |
| 2016 | PE24027 | closed | Loss of braking caused by rear brake hose failure | SERVICE BRAKES | 2024-10-03 | 2025-10-30 | 25V544 | On October 3, 2024, NHTSA’s Office of Defects Investigation (ODI) opened this Preliminary Evaluation to investigate instances of rear brake hose ruptures causing a sudden and unexpected loss of braking in model year (MY) 2015-2017 Ford Edge vehicles manufactured by Ford Motor Company. The complaints allege that, without warning, the vehicle lost its ability to brake causing an unanticipated increase in the vehicle’s stopping distance. The complaints also allege that, prior to the rear brake hose rupture event, the vehicle had been serviced under recall 20V-469. Recall 20V469 involved MY 2015-2 |
| 2015 | DP26008 | open | Loss of Motive Power | ENGINE AND ENGINE COOLING | 2026-09-03 | · | · | The Office of Defects Investigation (ODI) received a petition on August 5, 2026, requesting a defect investigation into the 2.0 Liter EcoBoost engine on model year 2015-2018 Ford Edge vehicles. The petition alleges that engine coolant intrusion results in a significant loss of engine power, accompanied by an "Engine Coolant Over Temperature" warning message. The petition further alleges that after the vehicle has sat and cooled down, the engine runs roughly and generates a check engine light for a cylinder misfire. This defect petition is being opened to evaluate the issue and determine whether to grant or deny the petition. The petition can be reviewed at NHTSA.gov under ODI number 11754989. |
| 2015 | EA21002 | open | Desiccated Air Bag Inflator Rupture | AIR BAGS:FRONTAL:DRIVER SIDE:INFLATOR MODULE | 2021-09-17 | · | · | From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open. |
| 2015 | PE24027 | closed | Loss of braking caused by rear brake hose failure | SERVICE BRAKES | 2024-10-03 | 2025-10-30 | 25V544 | On October 3, 2024, NHTSA’s Office of Defects Investigation (ODI) opened this Preliminary Evaluation to investigate instances of rear brake hose ruptures causing a sudden and unexpected loss of braking in model year (MY) 2015-2017 Ford Edge vehicles manufactured by Ford Motor Company. The complaints allege that, without warning, the vehicle lost its ability to brake causing an unanticipated increase in the vehicle’s stopping distance. The complaints also allege that, prior to the rear brake hose rupture event, the vehicle had been serviced under recall 20V-469. Recall 20V469 involved MY 2015-2 |
| 2014 | PE15020 | closed | Wheel Separation | WHEELS:RIM | 2015-05-20 | 2016-01-04 | · | On November 29, 2014, ODI received a complaint reporting the complete separation of an original equipment 22-inch alloy wheel rim mounted on the right front position of a model year 2014 Ford Edge vehicle (VOQ 10661278).The driver indicated that the right-front corner of the vehicle suddenly dropped while driving, causing the vehicle to go off the road to the right and into a field.The right-front wheel rim was found to have broken into two pieces. The owner said that there was no prior warning or wheel related problems with the vehicle. The vehicle had been driven approximately 8,500 miles at |
| 2013 | PE16012 | closed | Door Ajar Warning Light Always On | INTERIOR LIGHTING | 2016-09-28 | 2017-03-20 | · | The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the in |
| 2012 | PE16012 | closed | Door Ajar Warning Light Always On | INTERIOR LIGHTING | 2016-09-28 | 2017-03-20 | · | The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the in |
| 2011 | PE16012 | closed | Door Ajar Warning Light Always On | INTERIOR LIGHTING | 2016-09-28 | 2017-03-20 | · | The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the in |
Cite this
Derived data is CC BY 4.0. Link back to the page you used. Text and BibTeX below.
Wrench.Pro (2026). NHTSA investigations — Ford Edge [dataset]. https://www.wrench.pro/data/investigations/ford/edge
@misc{wrenchpro_investigations_ford_edge_2026,
author = {Wrench.Pro},
title = {Wrench.Pro NHTSA investigations: Ford Edge},
year = {2026},
howpublished = {\url{https://www.wrench.pro/data/investigations/ford/edge}},
note = {Derived from NHTSA public records. CC BY 4.0.}
}hub · known-issues · methodology · license · research (interpretation)