Lincoln MKZ: nhtsa investigations
All rows for this model in the NHTSA investigations dataset, newest model year first. Each year links to its consumer page, which shows the same records with context.
| rows | 22 |
|---|---|
| model years | 2010–2018 (9) |
| data through | 2026-09-20 |
| method | /data/methodology#investigations |
| license | CC BY 4.0 (derived) |
Vehicle pages
2018 · 2017 · 2016 · 2015 · 2014 · 2013 · 2012 · 2011 · 2010
Rows
| year | action_number | status | subject | components | opened | closed | recall_campaign | summary |
|---|---|---|---|---|---|---|---|---|
| 2018 | RQ22004 | closed | Front Brake Jounce Hose Failures | SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:HOSES, LINES/PIPING, AND FITTINGS | 2022-08-08 | 2023-03-24 | 23V162000 | On August 8, 2022, the Office of Defects Investigation (ODI) opened this investigation based on 50 Vehicle Owner Questionnaires (VOQs) alleging front brake jounce hose ruptures on model year (MY) 2013-2018 Ford Fusion and Lincoln MKZ vehicles. A ruptured front brake hose results in a brake fluid leak. As a result, the driver may experience an increase in pedal travel and a reduction in the rate of deceleration, increasing the risk of a crash. It should be noted that the subject vehicles identified fell outside the scope of NHTSA Safety Recall 20V-469, which addressed front brake hoses rupturin |
| 2017 | RQ22004 | closed | Front Brake Jounce Hose Failures | SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:HOSES, LINES/PIPING, AND FITTINGS | 2022-08-08 | 2023-03-24 | 23V162000 | On August 8, 2022, the Office of Defects Investigation (ODI) opened this investigation based on 50 Vehicle Owner Questionnaires (VOQs) alleging front brake jounce hose ruptures on model year (MY) 2013-2018 Ford Fusion and Lincoln MKZ vehicles. A ruptured front brake hose results in a brake fluid leak. As a result, the driver may experience an increase in pedal travel and a reduction in the rate of deceleration, increasing the risk of a crash. It should be noted that the subject vehicles identified fell outside the scope of NHTSA Safety Recall 20V-469, which addressed front brake hoses rupturin |
| 2016 | EA21002 | open | Desiccated Air Bag Inflator Rupture | AIR BAGS:FRONTAL:DRIVER SIDE:INFLATOR MODULE | 2021-09-17 | · | · | From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open. |
| 2016 | RQ19005 | closed | Door Latch Failures | LATCHES/LOCKS/LINKAGES:DOORS:LATCH | 2019-12-19 | 2022-02-07 | 20V177000 | In December 2019, the Office of Defects Investigation (ODI) opened this investigation based on 235 Vehicle Owner Questionnaires (VOQs) alleging doors failed to latch when closed, and/or inadvertently opened while driving, on model year (MY) 2012-2014 Ford Fiesta, and 2013-2014 Fusion and Lincoln MKZ. Some VOQs reported the failure occurred after the latch had been remedied under a prior recall which involved fracture of the latch pawl spring tab due to thermally induced cyclic fatigue. Other VOQs alleged a similar failure in vehicles not previously recalled. A latch with a fractured pawl sprin |
| 2016 | RQ22004 | closed | Front Brake Jounce Hose Failures | SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:HOSES, LINES/PIPING, AND FITTINGS | 2022-08-08 | 2023-03-24 | 23V162000 | On August 8, 2022, the Office of Defects Investigation (ODI) opened this investigation based on 50 Vehicle Owner Questionnaires (VOQs) alleging front brake jounce hose ruptures on model year (MY) 2013-2018 Ford Fusion and Lincoln MKZ vehicles. A ruptured front brake hose results in a brake fluid leak. As a result, the driver may experience an increase in pedal travel and a reduction in the rate of deceleration, increasing the risk of a crash. It should be noted that the subject vehicles identified fell outside the scope of NHTSA Safety Recall 20V-469, which addressed front brake hoses rupturin |
| 2015 | EA21002 | open | Desiccated Air Bag Inflator Rupture | AIR BAGS:FRONTAL:DRIVER SIDE:INFLATOR MODULE | 2021-09-17 | · | · | From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open. |
| 2015 | RQ19005 | closed | Door Latch Failures | LATCHES/LOCKS/LINKAGES:DOORS:LATCH | 2019-12-19 | 2022-02-07 | 20V177000 | In December 2019, the Office of Defects Investigation (ODI) opened this investigation based on 235 Vehicle Owner Questionnaires (VOQs) alleging doors failed to latch when closed, and/or inadvertently opened while driving, on model year (MY) 2012-2014 Ford Fiesta, and 2013-2014 Fusion and Lincoln MKZ. Some VOQs reported the failure occurred after the latch had been remedied under a prior recall which involved fracture of the latch pawl spring tab due to thermally induced cyclic fatigue. Other VOQs alleged a similar failure in vehicles not previously recalled. A latch with a fractured pawl sprin |
| 2015 | RQ22004 | closed | Front Brake Jounce Hose Failures | SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:HOSES, LINES/PIPING, AND FITTINGS | 2022-08-08 | 2023-03-24 | 23V162000 | On August 8, 2022, the Office of Defects Investigation (ODI) opened this investigation based on 50 Vehicle Owner Questionnaires (VOQs) alleging front brake jounce hose ruptures on model year (MY) 2013-2018 Ford Fusion and Lincoln MKZ vehicles. A ruptured front brake hose results in a brake fluid leak. As a result, the driver may experience an increase in pedal travel and a reduction in the rate of deceleration, increasing the risk of a crash. It should be noted that the subject vehicles identified fell outside the scope of NHTSA Safety Recall 20V-469, which addressed front brake hoses rupturin |
| 2014 | EA21002 | open | Desiccated Air Bag Inflator Rupture | AIR BAGS:FRONTAL:DRIVER SIDE:INFLATOR MODULE | 2021-09-17 | · | · | From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open. |
| 2014 | RQ19005 | closed | Door Latch Failures | LATCHES/LOCKS/LINKAGES:DOORS:LATCH | 2019-12-19 | 2022-02-07 | 20V177000 | In December 2019, the Office of Defects Investigation (ODI) opened this investigation based on 235 Vehicle Owner Questionnaires (VOQs) alleging doors failed to latch when closed, and/or inadvertently opened while driving, on model year (MY) 2012-2014 Ford Fiesta, and 2013-2014 Fusion and Lincoln MKZ. Some VOQs reported the failure occurred after the latch had been remedied under a prior recall which involved fracture of the latch pawl spring tab due to thermally induced cyclic fatigue. Other VOQs alleged a similar failure in vehicles not previously recalled. A latch with a fractured pawl sprin |
| 2014 | RQ22004 | closed | Front Brake Jounce Hose Failures | SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:HOSES, LINES/PIPING, AND FITTINGS | 2022-08-08 | 2023-03-24 | 23V162000 | On August 8, 2022, the Office of Defects Investigation (ODI) opened this investigation based on 50 Vehicle Owner Questionnaires (VOQs) alleging front brake jounce hose ruptures on model year (MY) 2013-2018 Ford Fusion and Lincoln MKZ vehicles. A ruptured front brake hose results in a brake fluid leak. As a result, the driver may experience an increase in pedal travel and a reduction in the rate of deceleration, increasing the risk of a crash. It should be noted that the subject vehicles identified fell outside the scope of NHTSA Safety Recall 20V-469, which addressed front brake hoses rupturin |
| 2013 | EA21002 | open | Desiccated Air Bag Inflator Rupture | AIR BAGS:FRONTAL:DRIVER SIDE:INFLATOR MODULE | 2021-09-17 | · | · | From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open. |
| 2013 | EA15002 | closed | Door Latch Failure | LATCHES/LOCKS/LINKAGES:DOORS:LATCH | 2015-02-27 | 2015-11-13 | 15V246000 | The Office of Defects Investigation (ODI) opened an investigation based on consumer allegations of doors failing to latch and/or inadvertently opening on model year (MY) 2011-2013 Ford Fiesta, MY 2013 Ford Fusion and MY 2013 Lincoln MKZ vehicles. All of the affected vehicles share the same door latch design.ODI has received 281 unique reports related to the alleged problem, with over 100 claiming that the door(s) opened inadvertently while the vehicle was in motion. There were no crashes reported however three separate injuries were indicated, all caused by a rebounding door striking a consume |
| 2013 | RQ19005 | closed | Door Latch Failures | LATCHES/LOCKS/LINKAGES:DOORS:LATCH | 2019-12-19 | 2022-02-07 | 20V177000 | In December 2019, the Office of Defects Investigation (ODI) opened this investigation based on 235 Vehicle Owner Questionnaires (VOQs) alleging doors failed to latch when closed, and/or inadvertently opened while driving, on model year (MY) 2012-2014 Ford Fiesta, and 2013-2014 Fusion and Lincoln MKZ. Some VOQs reported the failure occurred after the latch had been remedied under a prior recall which involved fracture of the latch pawl spring tab due to thermally induced cyclic fatigue. Other VOQs alleged a similar failure in vehicles not previously recalled. A latch with a fractured pawl sprin |
| 2013 | RQ22004 | closed | Front Brake Jounce Hose Failures | SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:HOSES, LINES/PIPING, AND FITTINGS | 2022-08-08 | 2023-03-24 | 23V162000 | On August 8, 2022, the Office of Defects Investigation (ODI) opened this investigation based on 50 Vehicle Owner Questionnaires (VOQs) alleging front brake jounce hose ruptures on model year (MY) 2013-2018 Ford Fusion and Lincoln MKZ vehicles. A ruptured front brake hose results in a brake fluid leak. As a result, the driver may experience an increase in pedal travel and a reduction in the rate of deceleration, increasing the risk of a crash. It should be noted that the subject vehicles identified fell outside the scope of NHTSA Safety Recall 20V-469, which addressed front brake hoses rupturin |
| 2012 | EA21002 | open | Desiccated Air Bag Inflator Rupture | AIR BAGS:FRONTAL:DRIVER SIDE:INFLATOR MODULE | 2021-09-17 | · | · | From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open. |
| 2012 | PE14030 | closed | Electric power steering failure | STEERING:ELECTRIC POWER ASSIST SYSTEM | 2014-10-02 | 2015-09-10 | 15V340000 | The Office of Defects Investigation (ODI) opened a preliminary evaluation to investigate complaints of the loss of power steering while driving. The subject vehicles are equipped with a rack mounted Electric Power Assisted Steering (EPAS) unit.Some of the complaints alleged that the steering assist failed and resulted in increased steering efforts that contributed to a loss of control and in some cases a crash.The EPAS system was manufactured by TRW Automotive for Ford and was designated as Generation I.These units were first produced and put into vehicle production in July 2008 beginning with |
| 2011 | EA12009 | closed | Floor mat interference with accelerator | VEHICLE SPEED CONTROL:ACCELERATOR PEDAL | 2012-12-12 | 2014-06-12 | 14E028000 | On May 27, 2014, Ford Motor Company submitted recall 14E-028 (Ford recall #14S07) to correct a safety-related problem with certain driver's side Ford optional all-weather floor mats sold for use in model year 2006 through 2011 model year Ford Fusion, Mercury Milan, Lincoln Zephyr, and Lincoln MKZ vehicles built at Hermosillo Assembly Plant (HAP) from November 9, 2007, to October 31 ,2010.NHTSA testing determined that the original accessory all-weather mat with a single retention clip (Figure 1), may interfere with accelerator pedal return to idle with the mat retained by the clip and rotated c |
| 2011 | PE14030 | closed | Electric power steering failure | STEERING:ELECTRIC POWER ASSIST SYSTEM | 2014-10-02 | 2015-09-10 | 15V340000 | The Office of Defects Investigation (ODI) opened a preliminary evaluation to investigate complaints of the loss of power steering while driving. The subject vehicles are equipped with a rack mounted Electric Power Assisted Steering (EPAS) unit.Some of the complaints alleged that the steering assist failed and resulted in increased steering efforts that contributed to a loss of control and in some cases a crash.The EPAS system was manufactured by TRW Automotive for Ford and was designated as Generation I.These units were first produced and put into vehicle production in July 2008 beginning with |
| 2010 | EA12009 | closed | Floor mat interference with accelerator | VEHICLE SPEED CONTROL:ACCELERATOR PEDAL | 2012-12-12 | 2014-06-12 | 14E028000 | On May 27, 2014, Ford Motor Company submitted recall 14E-028 (Ford recall #14S07) to correct a safety-related problem with certain driver's side Ford optional all-weather floor mats sold for use in model year 2006 through 2011 model year Ford Fusion, Mercury Milan, Lincoln Zephyr, and Lincoln MKZ vehicles built at Hermosillo Assembly Plant (HAP) from November 9, 2007, to October 31 ,2010.NHTSA testing determined that the original accessory all-weather mat with a single retention clip (Figure 1), may interfere with accelerator pedal return to idle with the mat retained by the clip and rotated c |
| 2010 | PE10019 | closed | Accel Pedal Interference - Acc Floormat | VEHICLE SPEED CONTROL:ACCELERATOR PEDAL | 2010-05-28 | 2013-01-11 | · | Unsecured mats may interfere with accelerator pedal return to idle. A heel blocker in the floor pan provides a platform that may lift an unsecured mat into contact with the pedal. Ford introduced new pedals as a running change early in model year (MY) 2010 vehicles. Analysis of complaints received by ODI and Ford show elevated rates of pedal entrapment incidents in MY 2008 through early 2010 production vehicles. Incidents typically occur following hard pedal applications to pass slower traffic or when merging into faster traffic. Drivers allege continued high engine power after releasing the a |
| 2010 | PE14030 | closed | Electric power steering failure | STEERING:ELECTRIC POWER ASSIST SYSTEM | 2014-10-02 | 2015-09-10 | 15V340000 | The Office of Defects Investigation (ODI) opened a preliminary evaluation to investigate complaints of the loss of power steering while driving. The subject vehicles are equipped with a rack mounted Electric Power Assisted Steering (EPAS) unit.Some of the complaints alleged that the steering assist failed and resulted in increased steering efforts that contributed to a loss of control and in some cases a crash.The EPAS system was manufactured by TRW Automotive for Ford and was designated as Generation I.These units were first produced and put into vehicle production in July 2008 beginning with |
Cite this
Derived data is CC BY 4.0. Link back to the page you used. Text and BibTeX below.
Wrench.Pro (2026). NHTSA investigations — Lincoln MKZ [dataset]. https://www.wrench.pro/data/investigations/lincoln/mkz
@misc{wrenchpro_investigations_lincoln_mkz_2026,
author = {Wrench.Pro},
title = {Wrench.Pro NHTSA investigations: Lincoln MKZ},
year = {2026},
howpublished = {\url{https://www.wrench.pro/data/investigations/lincoln/mkz}},
note = {Derived from NHTSA public records. CC BY 4.0.}
}hub · known-issues · methodology · license · research (interpretation)